New on LowEndTalk? Please Register and read our Community Rules.
All new Registrations are manually reviewed and approved, so a short delay after registration may occur before your account becomes active.
All new Registrations are manually reviewed and approved, so a short delay after registration may occur before your account becomes active.
Comments
Please let me know if this work for you
just did it on a new 4T box, upload went from 50M to 250-300M (using specific speedtest servers for the comparison of before / after)
@falzo @TheLinuxBug @Neoon is it possible to put the netboot kernel on /boot (and back it up) in case they replace it?
also thx Neoon for the discord!
can you tell me which file to delete exactly? this is what i have in /boot
System.map-4.9.58-armada375
uImage
config-4.9.58-armada375
uImage-4.9.58-armada375
I wasn't sure so I just backed them all and emptied the folder. I am guessing uImage* should suffice.
haha i did the same
before
after
just don't abuse the >250Mbit cause it's not nice & you 'll get hard limited
Hello,
About Stock on SyS, we are improving the delivery and we will continue during the next weeks. Sorry for the low stock the last weeks !
Also, we will soon (ETA week 32/33) provide SyS servers on other locations :
Also in case it might interest you :
About issues with our ARM and Kernels, if someone can tl;dr please do not sure I can help but at least i'll raise the issue internally.
Last but not least, GAME servers hasn't very much on OVH and SyS, if you are interested to discuss about it create a new topic or DM me.
We do not plan to provide preinstalled games nor licences but we can review our cpu/ram/disk/network ratios if needed for some legit uses cases (games or not).
and if you need something else (hourly payment etc) let's discuss it too ! Thx.
I didn't do anything to my 2TB storage box (Canada) and get 500/500 with speedtest-cli (speedtest server is also hosted by OVH)it might be just that but what's your kernel version? CF block youname command
Never mind. I "forgot" that I upgraded Ubuntu (I use scripts).
I peaked 160 mbps in transmission by setting it to prefer unencrypted connections. Encrypted it's more like 50 mbps. Is there a torrent client that can enforce unencrypted connections? edit: rtorrent@ 400 mbps
Seems like a decent value server if you can keep it as cpu-friendly as possible.
if that is 160mbits it's quite slow. was able to hit 45mbyte/s ~ 400mbits/s down with deluge and ltconfig. might wanna try it.
Deluge on this Arm server? CPU too slow, should it crashed it.
nah, it's slow at times but if you keep the torrent count low it works ok.
Any idea about how many weeks for Canada? I am trying to decide on you or a new provider and wanted to get an idea of about how long.
Which reference ?
Anyone got success enabling quota modules on SYS ARM servers?
@OVH_Matt @wokenwoll I got a network problem with SYS Essential servers. Two ranges (192.95.29.x and192.95.30.x) have low bandwidth from OVH Canada to OVH France. Asked the support but they say that is all ok. I have servers in other IP ranges and they reach 250Mbps to OVH France, but these two ranges does not. Please look at this:
iperf -c iperf.ovh.net -i 1
Client connecting to iperf.ovh.net, TCP port 5001
TCP window size: 85.0 KByte (default)
[ 3] local 192.95.30.173 port 51582 connected with 188.165.12.136 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 1.0 sec 11.4 MBytes 95.4 Mbits/sec
[ 3] 1.0- 2.0 sec 15.0 MBytes 126 Mbits/sec
[ 3] 2.0- 3.0 sec 15.0 MBytes 126 Mbits/sec
[ 3] 3.0- 4.0 sec 16.4 MBytes 137 Mbits/sec
[ 3] 4.0- 5.0 sec 17.9 MBytes 150 Mbits/sec
[ 3] 5.0- 6.0 sec 17.8 MBytes 149 Mbits/sec
[ 3] 6.0- 7.0 sec 19.1 MBytes 160 Mbits/sec
[ 3] 7.0- 8.0 sec 17.9 MBytes 150 Mbits/sec
[ 3] 8.0- 9.0 sec 20.5 MBytes 172 Mbits/sec
[ 3] 9.0-10.0 sec 19.1 MBytes 160 Mbits/sec
[ 3] 0.0-10.0 sec 170 MBytes 142 Mbits/sec
wget http://proof.ovh.net/files/10Gb.dat
--2018-07-03 12:27:46-- http://proof.ovh.net/files/10Gb.dat
A resolver proof.ovh.net (proof.ovh.net)...2001:41d0:2:876a::1, 188.165.12.106
A conectar proof.ovh.net (proof.ovh.net)2001:41d0:2:876a::1:80... conectado.
Pedido HTTP enviado, a aguardar resposta...200 OK
Tamanho: 1250000000 (1,2G) [application/octet-stream]
Saving to: ‘10Gb.dat’
10Gb.dat 100%[===================>] 1,16G 2,51MB/s in 5m 21s
2018-07-03 12:33:07 (3,72 MB/s) - ‘10Gb.dat’ saved [1250000000/1250000000]
Both tested in debian fresh install and rescue mode.
But when i test in OVH Canada, they perform amazing:
wget http://proof.ovh.ca/files/10Gio.dat
--2018-07-04 06:51:58-- http://proof.ovh.ca/files/10Gio.dat
Resolving proof.ovh.ca (proof.ovh.ca)... 192.99.19.165
Connecting to proof.ovh.ca (proof.ovh.ca)192.99.19.165:80... connected.
HTTP request sent, awaiting response... 200 OK
Length: 10737418240 (10G) [application/x-ns-proxy-autoconfig]
Saving to: ‘10Gio.dat’ 10Gio.dat 28%[=====> ] 2.84G 106MB/s eta 70s
The problem is not just iperf or wget to OVH France. In general that two ranges perform much worse than other ranges i have.
Sorry about that. I was interested in either the new E5-SAT-1-64 or the new E5-SAT-2-64.
I know there is a "fix" for the debian distro on SyS ARM servers. Did anyone get anywhere with a similar solution for ubuntu or is it impossible?
So, apparently you can order ARM in CA on with $ but not with €:
https://www.soyoustart.com/ie/server-storage/ does not work.
https://www.soyoustart.com/us/server-storage/ does work.
Well, the API says stock unknown, so I guess they will refund the orders but no idea.
No idea what fucked up at SYS.
Just install Debian 9 with distribution kernel and delete the uBoot armada file in /boot immediately after SSHing into the server. Reboot and then setup as needed. Works perfectly, no errors, and no stupid throttling.
Quoting myself, but this should work with Ubuntu too. I just find Debian much better (in Server edition ofc, Linux Mint for normal usage).
i got this files in /boot on debian
System.map-4.9.58-armada375 uImage
config-4.9.58-armada375 uImage-4.9.58-armada375
Which one should I delete?
uImage-4.9.58-armada375
Thanks @AC_Fan
Any successful installation of Nextcloud?
Sorry, I don't use NextCloud.
Yes. Working perfectly fine on my sys arm. Only 5 users, mainly for syncing. Performs well enough for personal use at least.
No stock on my side on both cases. looks like it was a refresh issue on the website (on our API)
Hello,
Since we have a lot of requests for our new references, when we know that we will connect new hosts in the next 10 days, we now allow "waiting lists".
It's prodded on 2 refs (E3-SAT-1-16 and E3-SAT-1-32), that's why you will see 10Days icon.
More refs will follow on SyS.
Of course, the "start time" of the service is the delivery date, not the order date.
Any idea on when you will roll out E5-SAT-1-64 or the new E5-SAT-2-64 in Canada?
You can solve this issue with these commands:
sudo rm -f /var/lib/dpkg/info/initramfs-tools.post*
sudo rm -f /var/lib/dpkg/info/initramfs-tools.pre*
sudo rm -f /var/lib/dpkg/info/bcmwl-kernel-source.post*
sudo rm -f /var/lib/dpkg/info/bcmwl-kernel-source.pre*
sudo dpkg --configure -a
After run again:
sudo apt install linux-image-4.4.0-21-generic linux-headers-generic
Info post: https://ubuntuforums.org/showthread.php?t=1990236